SPD Surge Protection Device AC Electronical Lightning Protection Device
Description:
Intensity of Remote Signalling Alarm Contact
Failure indication and centralized remote signalling alarm dry contacts;
High discharge capacity and low residual voltage;
Over-temperature protection;
IP20, UL94 V0
| Model Number | SUP1 |
| SPD according IEC 61643-1 | Class II |
| SPD according EN 61643-11 | Type 2 |
| Operating Temperature Range | -40ºC~+80ºC |
| Relative Humidity | ≤95%(25ºC) |
| Atmospheric Pressure | 86~106kPa |
| Working Frequency | 50/60Hz |
| Rated Working Voltage Uo | 230V/400V~ |
| Max Continuous Operating Voltage Uc(L-N) | 275V/320V/385V/420V ~ |
| Mode of protection | L-N/N-PE |
| Nominal Discharge Current In(8/20μs)(L-N) | 20kA |
| Max Discharge Current Imax (8/20μs) (L-N) | 40kA |
| Voltage Protection Level Up(L-N) | ≤1.2kV |
| Max. mains-side Overcurrent Protection | 80A(gL/gG) |
| Cross sectional area for wiring terminal connected to conductor | Stranded:4~25mm² Solid Wire: 4~35mm² |
| Max. Cross-sectional Area For Remote Signaling Interface | 1.5mm² |
| Torque: wiring terminal/remote signaling interface | 2.5Nm |
| Enclosure material | PBTV-0 |
| Degree of protection(IP code) | IP20 |
| Mounting | DIN35mm rails |
Solar DC SPD
The SUP series Surge Protection are designed to protect against lightning surge voltages in photovoltaic power supply networks.
These units must be installed in parallel on the DC networks to be protected and provide common and differential modes protection. The SUP series is available for the main operating voltages in photovoltaic: 1000 Vdc.
The use of SUP series Surge Protection is recommended at both ends of the DC power supply line (solar panel side and inverter/converter side),
Especially if the line routing is external and long. The electrical diagram of the SUN-S40 series is based on high energy PV equipped with specific thermal disconnectors and related failure indicators.
The SUP series is made with plug-in modules to allow a fast and easy maintenance in case of failure (disconnection from the DC network).
| SUP2-PV series surge protector | SUP4-PV | ||
| PV DC specific (LEC 6614-1/EN 61643-11) | |||
| Pole | 2 pole | 3 pole | |
| Electrical Parameter | |||
| Classifical test | II | II | |
| Uoc max (V DC) | 500 | 900 | |
| Uc (V DC) | 500 | 1000 | |
| In(8/20)us (KA) | 20 | 20 | |
| Imax(8/20)us (KA) | 40 | 40 | |
| Up (KV) | 2.0 | 3.8 | |
| Remote control and indication | |||
| Indication window | |||
| Plug-in module | |||
| Remote signal contact | |||
| Remote signal contact | Max working volt | 250V AC/30V DC | 250V AC/30V DC |
| Max working amp 1A (250V/AC) | 1A (250V/AC) | 1A (250V/AC) | |
| 1A (30V DC) | 1A (30V DC) | 1A (30V DC) | |
| Wiring & installation | |||
| Wiring capacity(mm2) | Hard wire | 4-25 | 4-25 |
|
 |
Flexible wire | 4-16 | 4-16 |
| Stripping length | 10 | 10 | |
| Terminal screwa | M5 | M5 | |
| Torque(Nm) | Main ciruit | 3.5 | 3.5 |
| Remote signal contact | 0.25 | 0.25 | |
| Protection class | All profile | IP40 | IP40 |
| Connection port | IP20 | IP20 | |
| Installation environment | No obvious shock and vibration | ||
| Altitude(m) | ≤ 2000 | ≤ 2000 | |
| Working temperature | -3.0--+70 | -3.0--+70 | |
| Relative humidity | 30%-90% | 30%-90% | |
| How to install | Install with H35-7.5/DIN35 stell mounting rail | ||
| Size(mm) (W*H*L) | W | 36 | 54 |
| H | 90 | 90 | |
| L | 67.6 | 67.6 | |
| Weight (KG) | 0.25 | 0.38 | |
| Nominal PV system volt | 600V | 100V | 1200V |
| MCOV(UCPV) | 700V DC | 1170V DC | 1200V DC |
| Max system discharge Current (8/20us) (Imax) | 40KA | 40KA | 30KA |
| Volt protection leve (UP) | ≤ 2.5KV | ≤ 4.0KV | ≤ 4.5KV |
| Volt protection Level at 5KA (UP) | ≤ 2.0KV | ≤ 3.5KV | ≤ 4.0KV |
| Integrate fuse breaking capacity/interrupting rating | 30KA/1000V DC | 30KA/1000V DC | 30KA/1200V DC |
| Technology | Short-circuit interruption (SCI) overcurrent protection | ||
| Operating temperature range | -40 to +80 | ||
| Nominal discharge current | 12.5KA | ||
| Response time (ta) | <25ns | ||
| Operating state/fault indication | Green (good) / Red (replace) | ||
| Mounting | 35mm DIN Rail per EN 60715 | ||
| Degree protection | IP20 | ||
| capacity | 3 modules DIN 43880 | ||
phone:008615067704943
This Xbox Series X Case including Carry Travel Bag For Xbox Series X Accessories and Xbox Series X Silicone Case.
the silicone case Keep your controller safe and protected in style with this silicone skin case. Compatible with Xbox Series X/S Controller. Add a splash of color to your controller and provide an instant all around protection from scratches, dirt, dust and grease caused by everyday use (and abuse). Excellent way to safeguard your controllers from accidental damage.Material is incredibly comfortable and gentle on skin. Soft and smooth to the touch. The skin adds almost no extra weight but rather enhance the texture.
The Xbox Series X Carry case bag specially designed for your Xbox Wireless Controller. Compatible with Xbox Series X,Xbox One X/Slim ,Xbox One/Elite controller.provides conservation for Xbox Series X Controller and your accessories ,the bag is partable ,mesh pocket accommodates USB cable and other small accessories conveniently.Great protection,stylish and durable,prevents any damages or scratches caused by accidentally bumping,dropping, secures the device in good condition on travelling or outdoors.
Xbox Series X Case,Storage Bag,Carry Travel For Xbox Series X Accessories,Carry Bag For Xbox Series X Controller
Shenzhen GEME electronics Co,.Ltd , https://www.gemeelectparts.com